Merge tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull devicetree updates from Rob Herring:

 - Convert various DT (non-binding) doc files to ReST

 - Various improvements to device link code

 - Fix __of_attach_node_sysfs refcounting bug

 - Add support for 'memory-region-names' with reserved-memory binding

 - Vendor prefixes for Protonic Holland, BeagleBoard.org, Alps, Check
   Point, Würth Elektronik, U-Boot, Vaisala, Baikal Electronics,
   Shanghai Awinic Technology Co., MikroTik, Silex Insight

 - A bunch more binding conversions to DT schema. Only 3K to go.

 - Add a minimum version check for schema tools

 - Treewide dropping of 'allOf' usage with schema references. Not needed
   in new json-schema spec.

 - Some formatting clean-ups of schemas

* tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (194 commits)
  dt-bindings: clock: Add documentation for X1830 bindings.
  dt-bindings: mailbox: Convert imx mu to json-schema
  dt-bindings: power: Convert imx gpcv2 to json-schema
  dt-bindings: power: Convert imx gpc to json-schema
  dt-bindings: Merge gpio-usb-b-connector with usb-connector
  dt-bindings: timer: renesas: cmt: Convert to json-schema
  dt-bindings: clock: Convert i.MX8QXP LPCG to json-schema
  dt-bindings: timer: Convert i.MX GPT to json-schema
  dt-bindings: thermal: rcar-thermal: Add device tree support for r8a7742
  dt-bindings: serial: Add binding for UART pin swap
  dt-bindings: geni-se: Add interconnect binding for GENI QUP
  dt-bindings: geni-se: Convert QUP geni-se bindings to YAML
  dt-bindings: vendor-prefixes: Add Silex Insight vendor prefix
  dt-bindings: input: touchscreen: edt-ft5x06: change reg property
  dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
  dt-bindings: timer: renesas: mtu2: Convert to json-schema
  of/fdt: Remove redundant kbasename function call
  dt-bindings: clock: Convert i.MX1 clock to json-schema
  dt-bindings: clock: Convert i.MX21 clock to json-schema
  dt-bindings: clock: Convert i.MX25 clock to json-schema
  ...

1 files changed, 0 insertions, 92 deletions

diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
deleted file mode 100644
index c02259353327..000000000000
--- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
+++ /dev/null
@@ -1,92 +0,0 @@
-* Ingenic JZ4780 NAND/ECC
-
-This file documents the device tree bindings for NAND flash devices on the
-JZ4780. NAND devices are connected to the NEMC controller (described in
-memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
-be children of the NEMC node.
-
-Required NAND controller device properties:
-- compatible: Should be one of:
-  * ingenic,jz4740-nand
-  * ingenic,jz4725b-nand
-  * ingenic,jz4780-nand
-- reg: For each bank with a NAND chip attached, should specify a bank number,
-  an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
-
-Optional NAND controller device properties:
-- ecc-engine: To make use of the hardware ECC controller, this
-  property must contain a phandle for the ECC controller node. The required
-  properties for this node are described below. If this is not specified,
-  software ECC will be used instead.
-
-Optional children nodes:
-- Individual NAND chips are children of the NAND controller node.
-
-Required children node properties:
-- reg: An integer ranging from 1 to 6 representing the CS line to use.
-
-Optional children node properties:
-- nand-ecc-step-size: ECC block size in bytes.
-- nand-ecc-strength: ECC strength (max number of correctable bits).
-- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
-- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false
-- rb-gpios: GPIO specifier for the busy pin.
-- wp-gpios: GPIO specifier for the write protect pin.
-
-Optional child node of NAND chip nodes:
-- partitions: see Documentation/devicetree/bindings/mtd/partition.txt
-
-Example:
-
-nemc: nemc@13410000 {
-	...
-
-	nandc: nand-controller@1 {
-		compatible = "ingenic,jz4780-nand";
-		reg = <1 0 0x1000000>;	/* Bank 1 */
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ecc-engine = <&bch>;
-
-		nand@1 {
-			reg = <1>;
-
-			nand-ecc-step-size = <1024>;
-			nand-ecc-strength = <24>;
-			nand-ecc-mode = "hw";
-			nand-on-flash-bbt;
-
-			rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>;
-			wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>;
-
-			partitions {
-				#address-cells = <2>;
-				#size-cells = <2>;
-				...
-			}
-		};
-	};
-};
-
-The ECC controller is a separate SoC component used for error correction on
-NAND devices. The following is a description of the device properties for a
-ECC controller.
-
-Required ECC properties:
-- compatible: Should be one of:
-  * ingenic,jz4740-ecc
-  * ingenic,jz4725b-bch
-  * ingenic,jz4780-bch
-- reg: Should specify the ECC controller registers location and length.
-- clocks: Clock for the ECC controller.
-
-Example:
-
-bch: bch@134d0000 {
-	compatible = "ingenic,jz4780-bch";
-	reg = <0x134d0000 0x10000>;
-
-	clocks = <&cgu JZ4780_CLK_BCH>;
-};